View SY87729L_5392704.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

SY87729L 3.3v anyclock ? , 10mhz to 365mhz fractional n synthesizer anyclock and anyrate are registered trademarks of micrel, inc. microwire is a trademark of national semiconductor micrel inc. ? 2180 fortune drive ? san jose, ca 95131 ? usa ? tel +1 ( 408 ) 944-0800 ? fax + 1 (408) 474-1000 ? http://www.micrel.com general description the SY87729L is a complete rate independent frequency synthesizer integrated circuit. from a single reference source, this device generates a differential pecl reference frequency for micrel's sy87721l 10mbps to 2.7gbps combined cdr and cmu. the SY87729L generates an exactly correct reference frequency for common data transport protocols. this is especially important in transponder applications, where a standards compliant protocol data unit must be generated downstream, even in the absence of any signal from the associated upstream interface. in addition, SY87729L will generate exactly correct reference frequencies for common data transport protocols augmented by forward error correction codes. for proprietary applications, the SY87729L generates reference frequencies guaranteed to enable the sy87721l cdr to lock to any possible baud rate in its range. SY87729L accepts configuration via a microwire? interface. data sheets and support documentation can be found on micrel?s web site at: www.micrel.com . anyclock ? features ? fractional synthesizer from 10mhz to 365mhz from a single 27mhz reference oscillator ? generates exactly the correct frequency for common transport protocols with or without fec ? directly enables sy87721l to lock onto any data rate within its range ? exceeds bellcore and itu jitter generation specifications ? programmable via microwire? interface ? available in 32-pin epad-tqfp package applications ? metro access system ? transponders ? multiplexers: access, add drop mux ? sonet/sdh/atm-based transmission systems, modules and test equipment ? broadband cross-connects ? fiber optic test equipment ? protocols supported: ? oc-1, oc-3, oc-12, oc-48, atm, gigabit ethernet, fast ethernet, fibre channel, 2x fibre channel, 1394, infiniband, proprietary optical transport july 2011 m9999-072111-g hbwhelp@micrel.com or (408) 955-1690
micrel, inc. SY87729L july 2011 2 m9999-072111-g hbwhelp@micrel.com ordering information (1) part number package type operating range package marking SY87729Lhy (3, 3) h32-2 industrial SY87729Lhy with pb-free bar-line indicator SY87729Lhytr (2, 3) h32-2 industrial SY87729Lhy with pb-free bar-line indicator notes: 1. contact factory for die availability. dice are guaranteed at t a = 25 c, dc electricals only. 2. tape and reel. 3. pb-free package is recommended for new designs. system block diagram or (408) 955-1690
micrel, inc. SY87729L july 2011 3 m9999-072111-g hbwhelp@micrel.com functional block diagram or (408) 955-1690
micrel, inc. SY87729L july 2011 4 m9999-072111-g hbwhelp@micrel.com pin configuration 32-pin epad tqfp (h32-2) pin description pin number pin name pin function 1, 24 vcca analog supply voltage. 2, 5,11, 12, 13, 15, 16, 19, 20, 23, 28, 29 nc no connection. these pins are to be left unconnected. 3, 4 refclk differential pecl input. . 6 progcs program interface chip select (t tl input). this signal forms part of the microwire? interface. when active high, this signal permits the acquisition of serial data. a falling edge on this input causes SY87729L to re-acquire lock to a new frequency, based on the program downloaded to it. 7 progdi program interface data in (ttl input). one dat a bit is sampled on each rising edge of prgsk, while progcs is active high. 8 progsk program interface serial clock (ttl input). one bit of configuration data is read in each clock cycle 9, 17 vcc supply voltage. 10 gnd ground. 14 locked lock output. this indicates proper operation of al l the blocks in the clock synthesis chain. logic high indicates that SY87729L is generating the expected frequency at the clkout output. logic low indicates that one or more pll in the clock synthesis chain has yet to achieve proper lock. 18 vcco output supply voltage. 21, 22 clkout reference clock output. this is the synthesiz ed clock generated from refclk. it can be used to supply a reference clock to a data recovery device, such as micrel?s sy87721l. 25, 32 gnda analog ground. 26, 27 wrvcf wrapper filter (analog i/o) . these pins connect to the output from the wrapper synthesizer charge pump, as well as the input to the corresponding vco. a filter network, as described below, converts the charge pump current to a voltage, and adjusts loop bandwidth 30, 31 fnvcf fractional-n filter (analog i/o) . these pins connect to the output from the fractional-n synthesizer charge pump, as well as the input to the corresponding voltage controlled oscillator (vco). a filter network, as described below, conv erts the charge pump current to a voltage, and adjusts loop bandwidth or (408) 955-1690
micrel, inc. SY87729L july 2011 5 m9999-072111-g hbwhelp@micrel.com or (408) 955-1690 absolute maximum ratings (1) supply voltage (v cc ).................................... ?0.5v to +4.0v input voltage (v in ). .................................... ?0.5v to v cc ecl output current (i out ) continuous............................................................50ma surge ..................................................................100ma lead temperature (solde ring, 20sec .) ....................... 260c storage temperature (t s ) .........................?65c to +150c operating ratings (2) supply voltage (v cc )...........................................+3.3v 5% ambient temperature (t a ) .......................... ?40c to +85c junction temper ature (t a) ........................................ 125 c package thermal resistance epad tqfp ( ja ) (3) still-air ...................................................... 27.6c/w 500lfpm .................................................... 20.7c/w dc electrical characteristics v cc = v cco = v cca = 3.3v 5%; gnd = gnda = 0v; t a = ?40c to +85c. symbol parameter condition min. typ. max. units v cc power supply voltage 3.15 3.3 3.45 v i cc power supply current no output load. ? 205 275 ma pecl dc electrical characteristics v cc = v cco = v cca = 3.3v 5%; gnd = gnda = 0v; t a = ?40c to +85c. symbol parameter condition min. typ. max. units v ih input high voltage v cc ? 1.165 ? v cc ? 0.880 v v il input low voltage v cc ? 1.810 ? v cc ? 1.475 v v oh output high voltage 50? to v cc ? 2v v cc ? 1.075 ? v cc ? 0.830 v v ol output low voltage 50? to v cc ? 2v v cc ? 1.860 ? v cc ? 1.570 v i il input low current (4, 5) v in = v il (min) ? 1.5 ? ? a ttl dc electrical characteristics v cc = v cco = v cca = 3.3v 5%; gnd = gnda = 0v; t a = ?40c to +85c. symbol parameter condition min. typ. max. units v ih input high voltage 2.0 ? ? v v il input low voltage ? ? 0.8 v v oh output high voltage i oh = ? 2ma 2.0 ? ? v v ol output low voltage i ol = 4ma ? ? 0.5 v v in = 2.7v, v cc = max ? ? + 20 i ih input high current v in = v cc , v cc = max ? ? + 100 a i il input low current (4, 5) v in = 0.5v, v cc = max ? ? ? 300 a i os output short-circuit current v out = 0v (1sec. max) ? 100 ? ? 250 ma notes: 1. permanent device damage may occur if absolute maximum ratings are exceeded. this is a stress rating only and functional oper ation is not implied at conditions other than those detailed in the operational sections of this data shee t. exposure to absolute maximum rating con ditions for extended periods may affect device reliability. 2. the data sheet limits are not guaranteed if t he device is operated beyond the operating ratings. 3. measured with die attach pad soldered to pcb, jedec-standard multi-layer board. 4. the refclk + pin has a nominal 75 ? pull-down resistor connected to ground. 5. the refclk ? pin has a nominal 75 ? pull-down resistor connected to ground and a nominal has a nominal 75 ? pull-up resistor connected to v cc .
micrel, inc. SY87729L july 2011 6 m9999-072111-g hbwhelp@micrel.com or (408) 955-1690 ac electrical characteristics v cc = v cco = v cca = 3.3v 5%; gnd = gnda = 0v; t a = ?40c to +85c. symbol parameter condition min. typ. max. units t irf refclk input rise/fall times ? ? 2.0 ns t refpwh refclk pulse width high 5 ? ? ns t refpwl refclk pulse width low 5 ? ? ns t cssk progcs-to-progsk preset 100 ? ? ns t skcs progsk-to-progcs recovery 100 ? ? ns t skp progsk period 200 ? ? ns t skpwh progsk pulse width high 70 ? ? ns t skpwl progsk pulse width low 70 ? ? ns t dis progdi data setup 20 ? ? ns t dih progdi data hold 20 ? ? ns clkout duty cycle t clkpwh /(t clkpwh + t clkpwl ) 25 ? 75 % of ui clkout maximum frequency 365 ? ? mhz acquisition lock time 27mhz reference clock ? ? 0.1 sec. fractional-n vco operating range 540 ? 729 mhz wrapper vco operating range 540 ? 729 mhz
micrel, inc. SY87729L july 2011 7 m9999-072111-g hbwhelp@micrel.com timing waveforms or (408) 955-1690
micrel, inc. SY87729L july 2011 8 m9999-072111-g hbwhelp@micrel.com functional description the SY87729L anyclock ? fractional-n synthesizer is used in serial data streaming applications, where the incoming data rate on a channel may vary, or where the incoming data rate on a channel is unknown ahead of time. in these situations, a valid output stream must still be generated even in the absence of any edges on the corresponding input stream. until now, designers had to resort to sub-optimal solutions such as providing multiple reference oscillators. beyond the potential noise and emi issues, the designer has no way to future proof his circuit, as it would prove near impossible to pre-provision all the reference frequencies that might be needed after deployment, yet are unknown at this time. the SY87729L solves this problem by generating exact frequencies for common data st reaming protocols, all from one 27mhz reference. if any of these protocols include overhead due to use of common digital wrappers, the SY87729L still generates the exact frequency required, including the overhead. besides generating reference rates for common protocols directly, the SY87729L also generates reference frequencies for micrel?s sy87721l cdr/cmu, such that it will reliably re cover data at any rate between 28mbps and 2,700mbps without any gaps. a simple 3-wire microwire? bit-serial interface loads a configuration that describes the desired output reference frequency. all common microcontrollers support this microwire? interface. those microcontrollers that don?t support this interface in hardware can easily emulate the interface in firmware. the large set of possible frequencies that the SY87729L generates, are divided into three classes. first, the sets of frequencies that match a particular data streaming protocol are in the ?protocol? category. second, the set of frequencies that are guaranteed to be near enough to any arbitrary data rate such that the sy87721l will lock are in the ?picket fence? category. third, the set of frequencies that do not fit into either of the first two categories is in the third category, the SY87729L generates these important reference frequencies through two tandem pll circuits. the first pll uses a modified fractional -n approach to generate a rational ratio frequency. this pll is capable of generating all protocol data rates, except for those that include fec or digital wrapper overhead. a second, more traditional p/q synthesizer optionally adjusts the output frequency of the first, fractional-n synthesizer, to accommodate these fec or digital wrapper data rates. the bit serial interface convey s 32 bits of configuration data from a microcontroller to SY87729L. this simple interface consists of an active high chip select, a serial clock (2mhz or less) and a serial data input. each clock cycle one bit of configuration data transfers to SY87729L. circuit description the heart of SY87729L is its fractional-n synthesizer, as shown in figure 1. figure 1. fractional-n synthesizer architecture the two dividers in the feedback path always differ by one count. that is, if one divider is set to divide by p = 5, then the other divider divides by p-1 = 4 . the mux chooses between the two based on the control circuit. the idea behind the fractional-n approach is that every input reference edge is used. only those output edges that are nearest to an input edge get fed back to the phase-frequency comparator. in addition, the nearest output edges are chosen in such a way that the net offset, over a number of edges, zeroes out. it is the control circuit?s job to drive the mux such that only the ?correct? edges get fed back. in the above fractional-n circuit, if the output frequency should be, for example, 5 times the input frequency, then p is set to 5, and the control circuit sets the mux to only feed back the output of the p divider. if the output frequency should be, for example, 4 1 / 2 times the input frequency, then the control circuit alternates evenly between the p and the p-1 divider output. for every two input edges (one to compare against p, and another to compare against p-1), you will get 5 + 4 output edges, yielding an output frequency 9/2 the input frequency. or (408) 955-1690
micrel, inc. SY87729L july 2011 9 m9999-072111-g hbwhelp@micrel.com whereas p sets the integer part of the multiplication factor from input to output frequency, the control circuit determines the fractional part. by mixing the output of the p and p-1 dividers correctly, the control circuit can fashion any output frequency from p-1 times the input to p times the input, as long as that ratio can be expressed as a ratio of integers. figure 2. 11/3 example figure 2 shows an example generating an output frequency 3 ? times the input frequency. since the output frequency is between 3 and 4 times the input, p is set to 4. we need to select the p divider twice, and select the p-1 divider once. multiplying by 4 two times out of three, and multiplying by 3 one time out of three, averages to a multiplication of 3 ? . the top waveform is the reference input. the bottom waveform is the multiplied output. the waveform in the middle shows those edges fr om the output that most closely matches a corresponding reference waveform edge. the control circuit must generate a repeating pattern to the mux of something like ?101,? so that the p divider is selected twice, and the p-1 divider is selected once, every three reference edges. fractional-n phase-frequency detector this circuit, besides generating ?pump up? and ?pump down? signals, also generates delta phase signals for use by the lock detect circuit. this detector circuit also accepts a gating signal from the fractional-n control block. when gated, the phase detector generates neither pump up nor pump down pulses. fractional-n charge pump this circuit converts the ?pump up? and ?pump down? signals from the phase-frequency detector into current pulses. an external loop filter integrates these current pulses into a control voltage. charge pump current is selectable. this modifies loop gain as follows: during acquisition of the reference, the charge pump current is fixed at 20a. once the acquisition sequencer has completed center frequency trimming, then it changes the current of this charge pump to 50a. fractional-n vco this circuit converts the voltage integrated by the external loop filter into a digital clock stream. the frequency of this clock varies based on this control voltage. this vco has a coarse and a fine input, with a combined range of 540mhz to 729mhz. the coarse input trims the vco, as described below, so that its center frequency rests near the target frequency to generate. the fine adjustment forms part of the closed loop. vco gain is nominally 200mhz per volt. fractional-n p/p-1 divider this is the main divider for the fractional-n loop. the logical value of the output of the control block (figure 1) defines whether the divider divides by p (values shown in table 1) or by p-1. the expression for the fractional division becomes: fractional division = p () ? ? ? ? ? ? ? ? + p q 1p q 1p q where q p is the number or reference clock periods during which the divider must divide by p and q p?1 is the number of reference clock periods during which the divider must divide by p-1. or (408) 955-1690
micrel, inc. SY87729L july 2011 10 m9999-072111-g hbwhelp@micrel.com care should be exercised when selecting the value of p (table 1) so that the voltage-controlled oscillator (vco) of the fractional-n pll is not driven out of range. the following conditions must be met: f vco (min) < f ref fractional division < f vco (max) or or (408) 955-1690 ) f vco (min) < f ref ( ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? + p q 1p q 1p q p < f vco (max) where, f vco (min) = 540mhz f vco (max) = 729mhz f ref = frequency of the reference clock divsel3 divsel2 divsel1 divsel0 p 0 0 0 0 17 0 0 0 1 18 0 0 1 0 19 0 0 1 1 20 0 1 0 0 21 0 1 0 1 22 0 1 1 0 23 0 1 1 1 24 1 0 0 0 25 1 0 0 1 26 1 0 1 0 27 1 0 1 1 28 1 1 0 0 29 1 1 0 1 30 1 1 1 0 31 1 1 1 1 32 table 1. divsel divider setting fractional-n control this circuit controls the p/p-1 divider, selecting the appropriate divide ratio, either p or p-1, in the correct pattern. as explained in the example of figure 2, controlling the p/p-1 divider amounts to generating a repeating binary bit stream. in that example, a ?1? represents dividing by 4, and a ?0? represents dividi ng by 3. the full cycle, ?101,? says to divide by 4 twice, and to divide by 3 once. in the general case, the pattern ?101? need not change based on the p divider value. to multiply by 14/3 instead of 11/3, for example, the same ?101? pattern would be used, but we would alternate dividing by 5 and 4, instead of dividing by 4 and 3. the p value, in effect, represents the integer part of the multiplication factor. the repeating binary bit pattern really depends only on the number of times to divide by p, and the number of times to divide by p-1. we label the number of times to divide by p as qp, and the number of times to divide by p-1 as qp?1. the fractional-n synthesizer generates its output frequency as per this formula: f fnout = ? ? ? ? ? ? ? ? + 1p q p q 1p q p f ref in our figure two example, we multiply by 11/3, or 4 - 1/3. matching against the formula, p = 4, qp?1 = 1, and qp = 2. the SY87729L accepts qp and qp?1 values from its microwire? interface, where they exist as the 5-bit values ?qp? and ?qpm1.? both values are unsigned binary numbers. qp and qp?1 are both constrained to be 31 or less, and their sum is also constrained to be 31 or less. that means that the denominator in the above formula must be 31 or less. as would be expected from the formula, setting qp to zero causes frequency multiplication exactly by p-1. setting qp?1 to zero causes frequency multiplication exactly by p. the SY87729L behavior is undefined if both qp and qp?1 are both set to zero. in the general case, the length of the repeating binary bit pattern is qp + qp?1. it consists of qp ?1?, and qp?1 ?0.?
micrel, inc. SY87729L july 2011 11 m9999-072111-g hbwhelp@micrel.com or (408) 955-1690 the SY87729L accomplishes this by implementing bresenham?s algorithm in hardware. to see how this works, we need a more complicated example. let?s say we need to multiply by 110/23, or 5 - 5/23. in this example, p = 5, qp?1 = 5, and qp = 18. the na?ve approach would generate a bit pattern of: 11111 11111 11111 11100 000 the spaces between groups of five digits are added for readability only. this pattern is 23 bits long, with qp (that is, 18) ?1? and qp?1 (that is, 5) ?0?, so it will multiply correctly, but it doesn?t match p/p-1 divider edges to input edges in the best way possible. in fact, the best pattern, in terms of minimizing distance between divider and reference input edges, is: 11110 11110 1110 11110 1110 table 2 shows how bresenham?s algorithm works. the first column is an accumulator. it starts at zero, but otherwise takes the result from the fourth column of the previous row. the second column is the value to add to the accumulator at each step. in the general case, this is always qp?1. the third co lumn forms the sum. the fourth column takes the sum modulo (qp + qp?1). the last column is ?0? whenever the modulo changes the sum. note that the table has 23 rows, before the sum is zero, and the entire algorithm repeats itself. accum add sum modulo bit 0 5 5 5 1 5 5 10 10 1 10 5 15 15 1 15 5 20 20 1 20 5 25 2 0 2 5 7 7 1 7 5 12 12 1 12 5 17 17 1 17 5 22 22 1 22 5 27 4 0 4 5 9 9 1 9 5 14 14 1 14 5 19 19 1 19 5 24 1 0 1 5 6 6 1 6 5 11 11 1 11 5 16 16 1 16 5 21 21 1 21 5 26 3 0 3 5 8 8 1 8 5 13 13 1 13 5 18 18 1 18 5 23 0 0 table 2. 5/23 example note that the sequence of bits in the last column, reading down, is the optimal pattern to generate. the choice of repeating bit pattern reduces jitter because a fractional-n synthesizer relies on edges temporarily not matching, but averaging out over some time interval. anything that reduces the timing disparity between edges arriving at the phase-frequency comparator will reduce jitter. center frequency trim this circuit block generates two identical reference voltages for the two vco on the SY87729L. this voltage pair can be digitally trimmed. trimming occurs under control of the acquisition sequencer, which trims for center frequency of the fractional-n synthesizer only. the wrapper synthesizer vco is matched to the fractional-n vco. both vco are fed the same coarse adjustment voltage, and so both center nominally at the same frequency.
micrel, inc. SY87729L july 2011 12 m9999-072111-g hbwhelp@micrel.com an 8-bit counter implements the voltage steps. the acquisition sequencer steps through this counter, which changes its voltage by about 12mv per step. the coarse input to the vco is nominally set at 500mhz per volt. the acquisition sequencer exercises the center frequency trim circuit so that the vco control voltage ends up within about 12mv of where it should be, were it exactly centered for the desired output frequency. lock detector the SY87729L ensures proper operation of both synthesizers by verifying that both pll have achieved lock. the locked output asserts active high only when this is the case, that is, both pll are locked. the SY87729L implements a digital lock detector that is both simple and robust. each phase-frequency detector provides a charge pump output that is the logical or of pump up and pump down pulses. the lock-detect circuit pr ocesses this charge pump output with a pulse width discriminator. once each reference clock rising edge, the discriminator will produce a pulse, only if the phase difference between the feedback divider and the reference input is too large. these pulses are subsequently processed digitally. a pll that is out of lock, is declared to be in lock only if 256 consecutive reference cl ocks have no large phase errors, as reported by the pulse-width discriminator. any large phase error event, even a single one, that arrives before lock is declared, will reset the circuit. once in lock, a pll is declared out of lock if more large- phase-difference than small-phase-difference events occur that is, if over time, a net of 256 large-phase- difference events occur. that is accomplished by counting up when large-phase-difference events occur and counting down in the case of small-phase events. wrapper synthesizer the frequency generated by the fractional-n pll is further processed by a more classical pll circuit, as shown in figure 3. or (408) 955-1690 figure 3. wrapper architecture this circuit further modifies the frequency generated by the fractional-n loop. this comes in handy where digital wrapper and/or fec is implemented. the wrapper synthesizer generates just a few ratios near 1. the wrapper modifies the frequency based on the values of m and n, the dividers, as per: 540mhz f wrout = ? ? ? ? ? ? + = qp1qp 1qp p m n fnout f m n wrapper phase-frequency detector this circuit generates pump up and pump down signals for the charge pump, and also generates delta phase for the lock detector. wrapper charge pump this circuit converts the pump signals from the phase- frequency detector into current pulses. charge pump current is fixed at about 20a. an external loop filter integrates these current pulses into a control voltage. wrapper vco this circuit matches the fractional-n vco in construction and operation, so that the c enter frequency trim circuit can center both the fractional-n vco and the wrapper vco at about the same frequency. wrapper m divider this circuit forms the denominator of the ratio by which the wrapper synthesizer modifies the fractional-n output frequency. the division ratio is selected via microwire?, as the 3-bit mdivsel register, as per table 3. mdivsel2 mdivsel2 mdivsel0 divisor 0 0 0 16 0 0 1 16 0 1 0 18 0 1 1 17 1 0 0 31 1 0 1 14 1 1 0 32 1 1 1 15 table 3. mdivsel divisor control
micrel, inc. SY87729L july 2011 13 m9999-072111-g hbwhelp@micrel.com the divisors are in two sets. the first set consists of the divisors 14, 15, 16, 17 and 18. the second set consists of 31 and 32. both m and n must be chosen from the same set. for example, an n divisor of 31 and an m divisor of 17 results in undefined behavior. the ? ? ? ? ? ? m n ratio must be kept smaller than 14 17 , that is, 14 18 is not allowed. wrapper n divider this circuit forms the numerator of the ratio by which the wrapper synthesizer modifies the fractional-n output frequency. the division ratio is selected via microwire?, as the 3-bit ndivsel register, as per table 4. ndivsel2 ndivsel2 ndivsel0 divisor 0 0 0 16 0 0 1 16 0 1 0 18 0 1 1 17 1 0 0 31 1 0 1 14 1 1 0 32 1 1 1 15 or (408) 955-1690 table 4. ndivsel divisor control p divider the output of the wrapper synthesizer is post divided down before appearing at the clkout pins. notice that, given the range of the wrapper vco (540mhz to 729mhz) and the maximum and minimum division ratios of the p divider (2 to 60, as shown in table 5), the minimum and maximum frequency of clkout is 9mhz and 364.5mhz respectively. postdivsel bit divisor 4 3 2 1 0 table 5. setting to prog ram the division ratio of the p divider
micrel, inc. SY87729L july 2011 14 m9999-072111-g hbwhelp@micrel.com the divisor value is selected via microwire?. the 5-bit postdivsel register determines the divisor value. it is set as per table 5. the SY87729L does not guarantee a 50% duty cycle output. it is designed to provide well- timed rising edges only. the SY87729L generates exact frequencies for common serial data streaming protocols. summary programming information appears in the next section. the SY87729L also enables micrel?s sy87721l anyrate ? cdr to decode virtually anything within its range of operation, all from a 27.000mhz reference. details about how to program the SY87729L in the general case, including derivation of programs for both the standard protocols and the anyrate ? application, appear in an applications note. microwire? interface this standard bit-serial interface eases interfacing the SY87729L to microcontrollers. the SY87729L accepts one data bit on progdi per rising edge on progsk. the data is ignored when progcs is inactive low. when progcs is active high, bits are shifted into the SY87729L. the falling edge of progcs then initiates acquisition of the output frequency defined by the 32-bit program just loaded into the SY87729L. standard protocol applications from a single 27.000mhz reference input, the SY87729L can generate exactly correct frequencies for at least the 18 protocols listed in table 7. this table also shows how to program the SY87729L for each protocol listed. this table assumes no digital wrapper. if your system includes such a wrapper, then modify the ndivsel and mdivsel bits accordingly. this means that, if the user wishes to re-acquire based on the same program, progcs needs to toggle high then low. programming loop filter values to program the SY87729L to generate a certain frequency: each pll in the SY87729L adjusts its loop gain through an external loop filter. figure 4 shows micrel?s recommended values for these. 1. determine the required values of the programming parameters, as summarized in table 6. 2. set progcs active high. 3. shift in each of the 32 bits, as per table 6. the fields are loaded in sequence, from the first row to the last row. for each multi-bit field, the most significant bit is shifted in first. shift the bits in through progdi, clocking them with progsk edges. 4. set progcs inactive low. 5. wait for locked to assert high. figure 4. recommended loop filter values field # bits reference preamble 4 always ?0000? qp 5 section: gating the p/p-1 divider qpm1 5 section: gating the p/p-1 divider divsel 4 table 1 mfg. 3 always ?000? postdivsel 5 table 5 ndivsel 3 table 4 mdivsel 3 table 3 table 6. programming sequence or (408) 955-1690
micrel, inc. SY87729L july 2011 15 m9999-072111-g hbwhelp@micrel.com or (408) 955-1690 protocol SY87729L f out (mhz) programming bits etr 32 0000 10011 01000 0111 000 10010 101 101 oc-1 51.84 0000 00001 11000 0111 000 01100 101 101 fast ethernet 50 0000 00010 11001 1000 000 01101 101 101 fddi 125 0000 00100 10111 0111 000 00101 101 101 1/8 fibre channel 13.28125 0000 01011 00111 0111 000 11100 101 101 general 150 0000 00010 00111 0110 000 00100 101 101 oc-3/stm-1 155.52 0000 00001 11000 0111 000 00100 101 101 escon 50 0000 00010 11001 1000 000 01101 101 101 1/4 fibre channel 26.5625 0000 01011 00111 0111 000 10100 101 101 1/2 fibre channel 53.125 0000 01011 00111 0111 000 01100 101 101 oc-12/stm-4 155.52 0000 00001 11000 0111 000 00100 101 101 fibre channel 106.25 0000 01011 00111 0111 000 00110 101 101 gigabit ethernet 156.25 0000 00100 10111 0111 000 00100 101 101 d1 video 69 0000 00001 00000 0110 000 01001 101 101 hdtv 92.8125 0000 00001 01111 1000 000 00111 101 101 infiniband 125 0000 00100 10111 0111 000 00100 101 101 2x fibre channel 212.5 0000 01011 00111 0111 000 00011 101 101 oc-48/stm-16 155.52 0000 00001 11000 0111 000 00100 101 101 table 7. protocol listings
micrel, inc. SY87729L july 2011 16 m9999-072111-g hbwhelp@micrel.com package information 32-pin epad tqfp ? die up (h32-2) or (408) 955-1690
micrel, inc. SY87729L july 2011 17 m9999-072111-g hbwhelp@micrel.com micrel, inc. 2180 fortune drive san jose, ca 95131 usa tel +1 (408) 944-0800 fax +1 (408) 474-1000 web http://www.micrel.com micrel makes no representations or warranties with respect to t he accuracy or completeness of the information furnished in this data sheet. this information is not intended as a warranty and micrel does not assume responsibility for it s use. micrel reserves the right to change circuitry, specifications and descriptions at any time without notice. no license, whether expre ss, implied, arising by estoppel or other wise, to any intellectual property rights is granted by this document. except as provided in micrel?s terms and conditions of sale for such products, mi crel assumes no liability whatsoever, and micrel disclaims any express or implied warranty relating to the sale and/or use of micrel products including l iability or warranties relating to fitness for a particular purpose, merchantability, or infringement of an y patent, copyright or other intellectual p roperty right. micrel products are not designed or authori zed for use as components in life support app liances, devices or systems where malfu nction of a product reasonably be expected to result in pers onal injury. life support devices or system s are devices or systems that (a) are in tended for surgical impla into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significan t injury to the user. a purchaser?s use or sale of micrel produc ts for use in life support app liances, devices or systems is a purchaser?s own risk and purchaser agrees to fully indemnify micrel for any damages resulting from such use or sale. can nt ? 2006 micrel, incorporated. or (408) 955-1690

▲Up To Search▲

Price & Availability of SY87729L

	To Download SY87729L Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .